AT88SC25616C
Figure 2.
Block Diagram
V CC
GND
SCL/CLK
SDA/IO
RST
Power
Management
Synchronous
Interface
Asynchronous
ISO Interface
Reset Block
Authentication,
Encryption and
Certification Unit
Data Transfer
Password
Verification
Answer to Reset
Random
Generator
EEPROM
2.
2.1.
2.2.
2.3.
2.4.
Pin Descriptions
Supply Voltage (V CC )
The V CC input is a 2.7V to 5.5V positive voltage supplied by the host.
Clock (SCL/CLK)
In the asynchronous T = 0 protocol, the SCL/CLK input is used to provide the device with a carrier frequency f . The
nominal length of one bit emitted on I/O is defined as an “elementary time unit” (ETU) and is equal to 372/ f . When the
synchronous protocol is used, the SCL/CLK input is used to positive edge clock data into the device and negative edge
clock data out of the device.
Reset (RST)
The AT88SC25616C provides an ISO 7816-3 compliant asynchronous answer to reset sequence. When the reset
sequence is activated, the device will output the data programmed into the 64-bit answer-to-reset register. An internal
pull-up on the RST input pad allows the device to be used in synchronous mode without bonding RST. The
AT88SC25616C does not support the synchronous answer-to-reset sequence.
Serial Data (SDA/IO)
The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wired with any number of
other open drain or open collector devices. An external pull-up resistor should be connected between SDA and VCC.
The value of this resistor and the system capacitance loading the SDA bus will determine the rise time of SDA. This
rise time will determine the maximum frequency during read operations. Low value pull-up resistors will allow higher
frequency operations while drawing higher average power. SDA/IO information applies to both asynchronous and
synchronous protocols.
When the synchronous protocol is used, the SCL/CLK input is used to positive edge clock data into the device and
negative edge clock data out of the device.
3
5017KJS–SMEM–08/09
相关PDF资料
AT88SC3216C-MJ IC EEPROM 32KBIT 1.5MHZ M2J
AT88SC6416C-MJ IC EEPROM 64KBIT 1.5MHZ M2J
AT91EB40A KIT EVAL FOR ARM AT91R40008
AT91EB42 KIT EVAL FOR ARM AT91M42800A
AT91EB55 KIT EVAL FOR ARM AT91M55800A
AT91SAM-ICE EMULATOR FOR AT91 ARM7/ARM9
AT91SAM7A3-EK KIT EVAL FOR AT91SAM7A3
AT91SAM7L-STK KIT EVAL FOR AT91SAM7L
相关代理商/技术参数
AT88SC25616C-MJTG 功能描述:电可擦除可编程只读存储器 CRYPTOMEMORY,256KBIT 16 ZONE RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT88SC25616C-MP 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:CryptoMemory 256 Kbit
AT88SC25616C-PI 功能描述:电可擦除可编程只读存储器 256k bit RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT88SC25616C-PU 功能描述:电可擦除可编程只读存储器 CRYPTOMEMORY 256kB 16 ZONE - 8 IND TEMP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT88SC25616CSDT 功能描述:KIT DEV TOOL CRYPTOMEMORY RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK(80-QFP ZIF 插口) 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
AT88SC25616C-SI 功能描述:电可擦除可编程只读存储器 256k bit RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT88SC25616C-SU 功能描述:电可擦除可编程只读存储器 CRYPTOMEMORY 256kB 16 ZONE - 8 IND TEMP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT88SC25616C-SU C0090 制造商:Atmel Corporation 功能描述:IC EEPROM 256KBIT 5MHZ 8SOIC